![]() You should play with the opacity and modes of both to find what you like for the In the light background example the settings were: In the example I used Glow Copy: Addition 60.0 You may play with the opacity of both to find the amount of glow you like. Set the mode on both GLOW copy and Glow layers to ADDITION Mode Rename the merged layer from Extrusion Copy to Glowįrom top down the order of the layers should be:Įxcept the top Glow copy layer, set it to 50.0 for a starting point. Right Click on one of the Glow Selection layers and With only the Glow Selection and Extrusion layers Visible.ĭuplicate the Glow Selection layer 4 or 5 times. Move the Extrusion Copy layer below the Glow Selection layer. In case something went wrong before this point.įinally, we will now make some custom GLOW layers. We will now clean up no longer needed layers that had been saved for backup Move the BR Logo layer above the Neon Selection layer Make the Neon Selection layer and the Extrusion layer both visibleĪnd right click on the Neon Selection layer to choose Merge Down. Right click the Neon Selection layer and choose Merge Downįrom the top menu: Filters > Render > 3d extrusionĪn Extrusion layer should appear directly beneath the Neon Selection layer Verify the Neon Selection layer is Visible and Active. (if neon doesn't work, check that Selection > None has been completed and try again.) Set foreground and background colors to FF00DE Use the Set Foreground / Background tool and Right click the GIMP LEARN BLACK layer and choose Alpha to Selction Make the GIMP LEARN BLACK layer active and the only Visible Name the Blur Subject copy GIMP LEARN BLACK Merge the duplicate layer down into the BR Logo layer. Rename the BR Logo Copy layer back to GIMP LEARN WHITE (BRL will not give an outcome on an all white subject)įilters > Alpha To Logo > Bevel Reflect Logo Use the Foreground/Background color Tool Set either one to Black andĭrag the black color to the selection and drop it. Right click on the layer and select Alpha to selection ![]() Make the GIMP LEARN WHITE layer the active layer and the only Visible layer Next we Prepare the GIMP LEARN WHITE layer for Bevel Reflect Logo. Right click the Blur Subject layer and select Make the Blur Subject layer the Active layer. Make a duplicate of the Visible layer and name it Blur Subject. It would be a good time to save your XCF file if you have not yet done so. Should now have a very clean set of the White Lines with Black "betweeners". I use eraser tool with a check in Hard Edge and set the zoom to 4) Now manually clean up if needed (if you forgot to turn antialias off in the text tool) Use the Fuzzy Select Tool and the key to remove all the black that is outside of the closed text.Ĭolors > Color to Alpha to remove red (color to alpha FF0000) So that the Visible layer is the only layer Visible. Make the Visible layer active, and set the other layers visibility to off, Right click int the Layers Tab box and select New From Visible. The background (black) layer should be visible. You should now have GIMP LEARN WHITE visible and below it, When you are done, set the Background layer visible and active and fill it with Black. Mask open ends of the white text with Red FF0000 (use pencil tool withīrush: Normal Nib 1 for the sharpest lines. Make sure GIMP LEARN WHITE is active and the only Visible layer. Right click this layer and select Alpha to Selectionĭrag the White boxfrom the foreground/background color tool and Right click this layer and select Layer to Image Size See small white squares in the 4 corners of the layerĬlick the middle icons on the top 2 lines in the Alignment tool settingsĪnd your text will center on your canvas size. Use the Alignment tool and click on your text layer so that you Right Click on the GIMP LEARN layer and select Alpha to Selection Then click again to position the text box (close to 0,0 the top left corner) With your text tool selected, click your mouse once so the cross-hairs display, Scroll your image over so the top left corner shows. Select the Text Tool and apply these settings:Īdjust letter spacing: 45.0 (for definition in extrusion) The E-Map used in this tutorial is included in the zip file along with a. Layer Effects is located from the Layers Tab, right click and Layer Effects Neon is located from the Paths Tab, right click and Decorate > Neon
0 Comments
Leave a Reply. |